SIDNEY — Using appropriate safety practices when working around grain is vital. Too many people ignore safety practices and suffer severe injury or death while working around grain. They get trapped in grain, tangled in auger flighting, or develop respiratory problems from exposure to grain dust and mold particles.

Grain bin dangers

Flowing grain will pull you into the grain mass, burying you within seconds. Never enter a bin while unloading grain or to break up a grain bridge. Stop the grain-conveying equipment and use the “lock-out/tag-out” procedures to secure it before entering the bin. Use a key-type padlock to lock the conveyor switch in the “off” position to ensure that the equipment does not start automatically or someone does not start it accidentally.

Bridging occurs when grain is high in moisture content, moldy, or in poor condition. The kernels stick together and form a crust. A cavity will form under the crust when grain is removed from the bin. The crust isn’t strong enough to support a person’s weight, so anyone who walks on it will fall into the cavity and be buried under several feet of grain.

To determine if the grain is bridged, look for a funnel shape on the surface of the grain mass after some grain has been removed. If the grain surface appears undisturbed, the grain has bridged and a cavity has formed under the surface. Stay outside the bin and use a pole or other object to break the bridge loose.

If the grain flow stops while you’re removing it from the bin but the grain surface has a funnel shape and shows some evidence that grain has been flowing into the auger, a chunk of spoiled grain probably is blocking the flow. Entering the bin to break up the blockage will expose you to being buried in grain and tangled in the auger. If grain has formed a vertical wall, try to break it up from the top of the bin with a long pole on a rope or through a door with a long pole. A wall of grain can collapse, or avalanche, without warning, knocking you over and burying you.

Never enter a grain bin alone. Have at least two people at the bin to assist in case of problems. Use a safety harness when entering a bin.

Rescuing a trapped person

If someone gets trapped:

1. Shut off all grain-moving equipment;

2. Contact your local emergency rescue service or fire department;

3. Ventilate the bin using the fan;

4. Form a retaining wall around the person using a rescue tube or plywood, sheet metal, or other material to keep grain from flowing toward the person, then remove grain from around the individual. Walking on the grain pushes more grain onto the trapped person.

Don’t try to pull a person out of grain. The grain exerts tremendous forces, so trying to pull someone out could damage the person’s spinal column or cause other damage.

Cut holes in the bin sides to remove grain if the person is submerged. Use a cutting torch, metal-cutting power saw, or air chisel to cut at least two V – or U-shaped holes on opposite sides or more holes equally spaced around the bin. Grain flowing from just one hole may injure the trapped person and cause the bin to collapse.

Dust and mold pose health hazards

Even low-level exposure to dust and mold can cause symptoms such as wheezing, a sore throat, congestion, and nasal or eye irritation. Higher concentrations can cause allergic reactions and trigger asthma episodes and other problems. Typical symptoms include shortness of breath; burning eyes; blurry vision; light sensitivity; a dry, hacking cough; and skin irritation. People may experience one or a combination of these symptoms.

In rare cases, severe symptoms, such as headaches, aches and pains, and/or fever may develop. People’s sensitivity varies based on the amount and type of mold. In addition, certain types of molds can produce mycotoxins, which increase the potential for health hazards from exposure to mold spores.

The minimum protection for anyone working around moldy grain should be an N-95-rated facemask. This mask has two straps to hold it firmly to the face and a metal strip over the nose to create a tight seal. A nuisance-dust mask with a single strap will not provide adequate protection.

Other dangers

Getting tangled in the unloading sweep auger is another major hazard. Entanglement typically results in lost feet, hands, arms, legs, and frequently death due to the severe damage. Although you shouldn’t enter a bin with an energized sweep auger, it may be necessary in some instances. All sweep augers should have guards that protect against contact with moving parts at the top and back. The only unguarded portion of the sweep auger should be the front point of operation.

If someone must go into the bin, make sure to have a rescue-trained and equipped observer positioned outside the storage bin. Use a safety switch that will allow the auger to operate only while the worker is in contact with the switch. Never use your hands or legs to manipulate the sweep auger while it’s in operation. The auger should have a bin stop device that prevents the sweep auger from making uncontrolled rotations.